2007-T3 Aluminum
2007-T3 aluminum is 2007 aluminum in the T3 temper. To achieve this temper, the metal is solution heat-treated, strain hardened, then naturally aged. The graph bars on the material properties cards below compare 2007-T3 aluminum to: 2000-series alloys (top), all aluminum alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Elastic (Young's, Tensile) Modulus
71 GPa 10 x 106 psi
Elongation at Break
6.8 %
Fatigue Strength
91 MPa 13 x 103 psi
Poisson's Ratio
0.33
Shear Modulus
27 GPa 3.9 x 106 psi
Shear Strength
230 MPa 33 x 103 psi
Tensile Strength: Ultimate (UTS)
390 MPa 56 x 103 psi
Tensile Strength: Yield (Proof)
250 MPa 36 x 103 psi
Thermal Properties
Latent Heat of Fusion
390 J/g
Maximum Temperature: Mechanical
190 °C 380 °F
Melting Completion (Liquidus)
640 °C 1180 °F
Melting Onset (Solidus)
510 °C 950 °F
Specific Heat Capacity
870 J/kg-K 0.21 BTU/lb-°F
Thermal Conductivity
130 W/m-K 75 BTU/h-ft-°F
Thermal Expansion
23 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
47 % IACS
Electrical Conductivity: Equal Weight (Specific)
140 % IACS
Otherwise Unclassified Properties
Base Metal Price
11 % relative
Density
3.1 g/cm3 190 lb/ft3
Embodied Carbon
8.0 kg CO2/kg material
Embodied Energy
150 MJ/kg 63 x 103 BTU/lb
Embodied Water
1130 L/kg 130 gal/lb
Common Calculations
Resilience: Ultimate (Unit Rupture Work)
23 MJ/m3
Resilience: Unit (Modulus of Resilience)
430 kJ/m3
Stiffness to Weight: Axial
13 points
Stiffness to Weight: Bending
44 points
Strength to Weight: Axial
35 points
Strength to Weight: Bending
38 points
Thermal Diffusivity
48 mm2/s
Thermal Shock Resistance
17 points
Alloy Composition
| Al | 87.5 to 95 | |
| Cu | 3.3 to 4.6 | |
| Pb | 0.8 to 1.5 | |
| Mg | 0.4 to 1.8 | |
| Mn | 0.5 to 1.0 | |
| Si | 0 to 0.8 | |
| Fe | 0 to 0.8 | |
| Zn | 0 to 0.8 | |
| Ni | 0 to 0.2 | |
| Ti | 0 to 0.2 | |
| Sn | 0 to 0.2 | |
| Bi | 0 to 0.2 | |
| Cr | 0 to 0.1 | |
| res. | 0 to 0.3 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Further Reading
EN 754-2: Aluminium and aluminium alloys. Cold drawn rod/bar and tube. Mechanical properties
Aluminum: Properties and Physical Metallurgy, John E. Hatch (editor), 1984
EN 755-2: Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Mechanical properties
EN 573-3: Aluminium and aluminium alloys. Chemical composition and form of wrought products. Chemical composition and form of products
Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM Handbook vol. 2, ASM International, 1993