2007-T4510 Aluminum
2007-T4510 aluminum is 2007 aluminum in the T4510 temper. To achieve this temper, the metal is solution heat-treated, stress relieved, then naturally aged. The stress relief is accomplished by stretching the metal by an amount that depends on the type of standard wrought product being made (extrusion or tube). The metal is not straightened after the stretching operation. This temper is closely related to T4511, which permits such straightening.
It has the lowest strength compared to the other variants of 2007 aluminum.
The graph bars on the material properties cards below compare 2007-T4510 aluminum to: 2000-series alloys (top), all aluminum alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Elastic (Young's, Tensile) Modulus
71 GPa 10 x 106 psi
Elongation at Break
7.8 %
Fatigue Strength
110 MPa 16 x 103 psi
Poisson's Ratio
0.33
Shear Modulus
27 GPa 3.9 x 106 psi
Shear Strength
220 MPa 32 x 103 psi
Tensile Strength: Ultimate (UTS)
370 MPa 54 x 103 psi
Tensile Strength: Yield (Proof)
240 MPa 35 x 103 psi
Thermal Properties
Latent Heat of Fusion
390 J/g
Maximum Temperature: Mechanical
190 °C 380 °F
Melting Completion (Liquidus)
640 °C 1180 °F
Melting Onset (Solidus)
510 °C 950 °F
Specific Heat Capacity
870 J/kg-K 0.21 BTU/lb-°F
Thermal Conductivity
130 W/m-K 75 BTU/h-ft-°F
Thermal Expansion
23 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
47 % IACS
Electrical Conductivity: Equal Weight (Specific)
140 % IACS
Otherwise Unclassified Properties
Base Metal Price
11 % relative
Density
3.1 g/cm3 190 lb/ft3
Embodied Carbon
8.0 kg CO2/kg material
Embodied Energy
150 MJ/kg 63 x 103 BTU/lb
Embodied Water
1130 L/kg 130 gal/lb
Common Calculations
Resilience: Ultimate (Unit Rupture Work)
26 MJ/m3
Resilience: Unit (Modulus of Resilience)
410 kJ/m3
Stiffness to Weight: Axial
13 points
Stiffness to Weight: Bending
44 points
Strength to Weight: Axial
33 points
Strength to Weight: Bending
37 points
Thermal Diffusivity
48 mm2/s
Thermal Shock Resistance
16 points
Alloy Composition
| Al | 87.5 to 95 | |
| Cu | 3.3 to 4.6 | |
| Pb | 0.8 to 1.5 | |
| Mg | 0.4 to 1.8 | |
| Mn | 0.5 to 1.0 | |
| Si | 0 to 0.8 | |
| Fe | 0 to 0.8 | |
| Zn | 0 to 0.8 | |
| Ni | 0 to 0.2 | |
| Ti | 0 to 0.2 | |
| Sn | 0 to 0.2 | |
| Bi | 0 to 0.2 | |
| Cr | 0 to 0.1 | |
| res. | 0 to 0.3 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Further Reading
Aluminum: Properties and Physical Metallurgy, John E. Hatch (editor), 1984
EN 755-2: Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Mechanical properties
EN 573-3: Aluminium and aluminium alloys. Chemical composition and form of wrought products. Chemical composition and form of products
Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM Handbook vol. 2, ASM International, 1993