5182-H111 Aluminum
5182-H111 aluminum is 5182 aluminum in the H111 temper. To achieve this temper, the metal is strain hardened to a strength that is lower than what is permissible for H11 (1/8-hard). The graph bars on the material properties cards below compare 5182-H111 aluminum to: 5000-series alloys (top), all aluminum alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Brinell Hardness
69
Elastic (Young's, Tensile) Modulus
68 GPa 9.8 x 106 psi
Elongation at Break
12 %
Fatigue Strength
100 MPa 15 x 103 psi
Poisson's Ratio
0.33
Shear Modulus
25 GPa 3.7 x 106 psi
Shear Strength
170 MPa 25 x 103 psi
Tensile Strength: Ultimate (UTS)
280 MPa 41 x 103 psi
Tensile Strength: Yield (Proof)
130 MPa 18 x 103 psi
Thermal Properties
Latent Heat of Fusion
390 J/g
Maximum Temperature: Mechanical
180 °C 360 °F
Melting Completion (Liquidus)
640 °C 1180 °F
Melting Onset (Solidus)
590 °C 1090 °F
Specific Heat Capacity
900 J/kg-K 0.22 BTU/lb-°F
Thermal Conductivity
130 W/m-K 74 BTU/h-ft-°F
Thermal Expansion
24 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
28 % IACS
Electrical Conductivity: Equal Weight (Specific)
94 % IACS
Otherwise Unclassified Properties
Base Metal Price
9.5 % relative
Density
2.7 g/cm3 170 lb/ft3
Embodied Carbon
8.9 kg CO2/kg material
Embodied Energy
150 MJ/kg 66 x 103 BTU/lb
Embodied Water
1180 L/kg 140 gal/lb
Common Calculations
Resilience: Ultimate (Unit Rupture Work)
28 MJ/m3
Resilience: Unit (Modulus of Resilience)
120 kJ/m3
Stiffness to Weight: Axial
14 points
Stiffness to Weight: Bending
51 points
Strength to Weight: Axial
29 points
Strength to Weight: Bending
36 points
Thermal Diffusivity
53 mm2/s
Thermal Shock Resistance
12 points
Alloy Composition
| Al | 93.2 to 95.8 | |
| Mg | 4.0 to 5.0 | |
| Mn | 0.2 to 0.5 | |
| Fe | 0 to 0.35 | |
| Zn | 0 to 0.25 | |
| Si | 0 to 0.2 | |
| Cu | 0 to 0.15 | |
| Cr | 0 to 0.1 | |
| Ti | 0 to 0.1 | |
| res. | 0 to 0.15 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Further Reading
Handbook of Aluminum Bonding Technology and Data, J. D. Minford, 1993
Advanced Materials in Automotive Engineering, Jason Rowe (editor), 2012
EN 485-2: Aluminium and aluminium alloys. Sheet, strip and plate. Mechanical properties
EN 573-3: Aluminium and aluminium alloys. Chemical composition and form of wrought products. Chemical composition and form of products
CRC Materials Science and Engineering Handbook, 4th ed., James F. Shackelford et al. (editors), 2015