6110A-T5 Aluminum
6110A-T5 aluminum is 6110A aluminum in the T5 temper. To achieve this temper, the metal is artificially aged until it meets standard mechanical property requirements. The graph bars on the material properties cards below compare 6110A-T5 aluminum to: 6000-series alloys (top), all aluminum alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Elastic (Young's, Tensile) Modulus
70 GPa 10 x 106 psi
Elongation at Break
11 %
Fatigue Strength
210 MPa 30 x 103 psi
Poisson's Ratio
0.33
Shear Modulus
26 GPa 3.8 x 106 psi
Shear Strength
250 MPa 37 x 103 psi
Tensile Strength: Ultimate (UTS)
430 MPa 62 x 103 psi
Tensile Strength: Yield (Proof)
410 MPa 60 x 103 psi
Thermal Properties
Latent Heat of Fusion
410 J/g
Maximum Temperature: Mechanical
190 °C 370 °F
Melting Completion (Liquidus)
650 °C 1200 °F
Melting Onset (Solidus)
600 °C 1110 °F
Specific Heat Capacity
900 J/kg-K 0.21 BTU/lb-°F
Thermal Conductivity
160 W/m-K 93 BTU/h-ft-°F
Thermal Expansion
23 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
42 % IACS
Electrical Conductivity: Equal Weight (Specific)
140 % IACS
Otherwise Unclassified Properties
Base Metal Price
9.5 % relative
Density
2.8 g/cm3 170 lb/ft3
Embodied Carbon
8.4 kg CO2/kg material
Embodied Energy
150 MJ/kg 66 x 103 BTU/lb
Embodied Water
1170 L/kg 140 gal/lb
Common Calculations
Resilience: Ultimate (Unit Rupture Work)
47 MJ/m3
Resilience: Unit (Modulus of Resilience)
1210 kJ/m3
Stiffness to Weight: Axial
14 points
Stiffness to Weight: Bending
50 points
Strength to Weight: Axial
43 points
Strength to Weight: Bending
46 points
Thermal Diffusivity
65 mm2/s
Thermal Shock Resistance
19 points
Alloy Composition
| Al | 94.8 to 98 | |
| Si | 0.7 to 1.1 | |
| Mg | 0.7 to 1.1 | |
| Mn | 0.3 to 0.9 | |
| Cu | 0.3 to 0.8 | |
| Fe | 0 to 0.5 | |
| Cr | 0.050 to 0.25 | |
| Ti | 0 to 0.2 | |
| Zr | 0 to 0.2 | |
| Zn | 0 to 0.2 | |
| res. | 0 to 0.15 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Further Reading
Aluminum: Properties and Physical Metallurgy, John E. Hatch (editor), 1984
EN 755-2: Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Mechanical properties
EN 573-3: Aluminium and aluminium alloys. Chemical composition and form of wrought products. Chemical composition and form of products