6262-T651 Aluminum
6262-T651 aluminum is 6262 aluminum in the T651 temper. To achieve this temper, the metal is solution heat-treated, stress relieved, then artificially aged. The stress relief is accomplished by stretching the metal by an amount that depends on the type of standard wrought product being made (sheet, plate, bar, or forging).
The graph bars on the material properties cards below compare 6262-T651 aluminum to: 6000-series alloys (top), all aluminum alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Elastic (Young's, Tensile) Modulus
68 GPa 9.9 x 106 psi
Elongation at Break
10 %
Fatigue Strength
110 MPa 16 x 103 psi
Poisson's Ratio
0.33
Shear Modulus
26 GPa 3.7 x 106 psi
Shear Strength
190 MPa 28 x 103 psi
Tensile Strength: Ultimate (UTS)
320 MPa 47 x 103 psi
Tensile Strength: Yield (Proof)
270 MPa 40 x 103 psi
Thermal Properties
Latent Heat of Fusion
400 J/g
Maximum Temperature: Mechanical
160 °C 330 °F
Melting Completion (Liquidus)
650 °C 1200 °F
Melting Onset (Solidus)
580 °C 1080 °F
Specific Heat Capacity
890 J/kg-K 0.21 BTU/lb-°F
Thermal Conductivity
170 W/m-K 99 BTU/h-ft-°F
Thermal Expansion
23 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
44 % IACS
Electrical Conductivity: Equal Weight (Specific)
140 % IACS
Otherwise Unclassified Properties
Base Metal Price
10 % relative
Density
2.8 g/cm3 180 lb/ft3
Embodied Carbon
8.3 kg CO2/kg material
Embodied Energy
150 MJ/kg 66 x 103 BTU/lb
Embodied Water
1190 L/kg 140 gal/lb
Common Calculations
Resilience: Ultimate (Unit Rupture Work)
31 MJ/m3
Resilience: Unit (Modulus of Resilience)
550 kJ/m3
Stiffness to Weight: Axial
13 points
Stiffness to Weight: Bending
48 points
Strength to Weight: Axial
32 points
Strength to Weight: Bending
37 points
Thermal Diffusivity
69 mm2/s
Thermal Shock Resistance
15 points
Alloy Composition
| Al | 94.7 to 97.8 | |
| Mg | 0.8 to 1.2 | |
| Si | 0.4 to 0.8 | |
| Pb | 0.4 to 0.7 | |
| Bi | 0.4 to 0.7 | |
| Fe | 0 to 0.7 | |
| Cu | 0.15 to 0.4 | |
| Zn | 0 to 0.25 | |
| Cr | 0.040 to 0.14 | |
| Mn | 0 to 0.15 | |
| Ti | 0 to 0.15 | |
| res. | 0 to 0.15 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Further Reading
ASTM B211: Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire
ASTM B210: Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
ASTM B221: Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
Aluminum Standards and Data, Aluminum Association Inc., 2013
EN 573-3: Aluminium and aluminium alloys. Chemical composition and form of wrought products. Chemical composition and form of products
Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM Handbook vol. 2, ASM International, 1993