7010-T76 Aluminum
7010-T76 aluminum is 7010 aluminum in the T76 temper. To achieve this temper, the metal is solution heat-treated and stabilized by artificial overaging. The degree of overaging is chosen so as to maximize exfoliation corrosion resistance.
The graph bars on the material properties cards below compare 7010-T76 aluminum to: 7000-series alloys (top), all aluminum alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Elastic (Young's, Tensile) Modulus
70 GPa 10 x 106 psi
Elongation at Break
5.7 %
Fatigue Strength
180 MPa 26 x 103 psi
Poisson's Ratio
0.32
Shear Modulus
26 GPa 3.8 x 106 psi
Shear Strength
340 MPa 49 x 103 psi
Tensile Strength: Ultimate (UTS)
580 MPa 84 x 103 psi
Tensile Strength: Yield (Proof)
490 MPa 71 x 103 psi
Thermal Properties
Latent Heat of Fusion
380 J/g
Maximum Temperature: Mechanical
200 °C 380 °F
Melting Completion (Liquidus)
630 °C 1170 °F
Melting Onset (Solidus)
480 °C 890 °F
Specific Heat Capacity
860 J/kg-K 0.21 BTU/lb-°F
Thermal Conductivity
150 W/m-K 88 BTU/h-ft-°F
Thermal Expansion
24 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
40 % IACS
Electrical Conductivity: Equal Weight (Specific)
120 % IACS
Otherwise Unclassified Properties
Base Metal Price
10 % relative
Density
3.0 g/cm3 190 lb/ft3
Embodied Carbon
8.3 kg CO2/kg material
Embodied Energy
150 MJ/kg 64 x 103 BTU/lb
Embodied Water
1120 L/kg 130 gal/lb
Common Calculations
Resilience: Ultimate (Unit Rupture Work)
31 MJ/m3
Resilience: Unit (Modulus of Resilience)
1720 kJ/m3
Stiffness to Weight: Axial
13 points
Stiffness to Weight: Bending
45 points
Strength to Weight: Axial
53 points
Strength to Weight: Bending
51 points
Thermal Diffusivity
58 mm2/s
Thermal Shock Resistance
25 points
Alloy Composition
| Al | 87.9 to 90.6 | |
| Zn | 5.7 to 6.7 | |
| Mg | 2.1 to 2.6 | |
| Cu | 1.5 to 2.0 | |
| Zr | 0.1 to 0.16 | |
| Fe | 0 to 0.15 | |
| Si | 0 to 0.12 | |
| Mn | 0 to 0.1 | |
| Ti | 0 to 0.060 | |
| Cr | 0 to 0.050 | |
| Ni | 0 to 0.050 | |
| res. | 0 to 0.15 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Further Reading
Handbook of Aluminum vol. 2: Alloy Production and Materials Manufacturing, George Totten and D. Scott MacKenzie (editors), 2003
EN 485-2: Aluminium and aluminium alloys. Sheet, strip and plate. Mechanical properties
ASM Specialty Handbook: Aluminum and Aluminum Alloys, J. R. Davis (editor), 1993
ISO 6361-2: Wrought aluminium and aluminium alloys - Sheets, strips and plates - Part 2: Mechanical properties
EN 573-3: Aluminium and aluminium alloys. Chemical composition and form of wrought products. Chemical composition and form of products