Normalized and Tempered (+NT) 1.1181 Steel
EN 1.1181 +NT steel is EN 1.1181 steel in the normalized and tempered condition. The graph bars on the material properties cards below compare EN 1.1181 +NT steel to: wrought carbon or non-alloy steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Brinell Hardness
160
Elastic (Young's, Tensile) Modulus
190 GPa 27 x 106 psi
Elongation at Break
19 %
Fatigue Strength
190 MPa 28 x 103 psi
Impact Strength: V-Notched Charpy
23 J 17 ft-lb
Poisson's Ratio
0.29
Shear Modulus
73 GPa 11 x 106 psi
Shear Strength
350 MPa 51 x 103 psi
Tensile Strength: Ultimate (UTS)
560 MPa 81 x 103 psi
Tensile Strength: Yield (Proof)
280 MPa 41 x 103 psi
Thermal Properties
Latent Heat of Fusion
250 J/g
Maximum Temperature: Mechanical
400 °C 750 °F
Melting Completion (Liquidus)
1460 °C 2660 °F
Melting Onset (Solidus)
1420 °C 2590 °F
Specific Heat Capacity
470 J/kg-K 0.11 BTU/lb-°F
Thermal Conductivity
42 W/m-K 24 BTU/h-ft-°F
Thermal Expansion
11 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
7.2 % IACS
Electrical Conductivity: Equal Weight (Specific)
8.3 % IACS
Otherwise Unclassified Properties
Base Metal Price
2.1 % relative
Density
7.8 g/cm3 490 lb/ft3
Embodied Carbon
1.4 kg CO2/kg material
Embodied Energy
19 MJ/kg 8.2 x 103 BTU/lb
Embodied Water
47 L/kg 5.6 gal/lb
Common Calculations
Resilience: Ultimate (Unit Rupture Work)
90 MJ/m3
Resilience: Unit (Modulus of Resilience)
210 kJ/m3
Stiffness to Weight: Axial
13 points
Stiffness to Weight: Bending
24 points
Strength to Weight: Axial
20 points
Strength to Weight: Bending
19 points
Thermal Diffusivity
11 mm2/s
Thermal Shock Resistance
19 points
Alloy Composition
| Fe | 97.4 to 99.18 | |
| Mn | 0.5 to 0.8 | |
| C | 0.32 to 0.39 | |
| Si | 0 to 0.4 | |
| Cr | 0 to 0.4 | |
| Ni | 0 to 0.4 | |
| Mo | 0 to 0.1 | |
| P | 0 to 0.035 | |
| S | 0 to 0.035 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Further Reading
EN 10250-2: Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels
EN 10269: Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
Creep-Resistant Steels, Fujio Abe et al. (editors), 2008
Carbon Steel Handbook, D. Gandy, 2007
ASM Specialty Handbook: Carbon and Alloy Steels, J. R. Davis (editor), 1996
Ferrous Materials: Steel and Cast Iron, Hans Berns and Werner Theisen, 2008
Steels: Processing, Structure, and Performance, 2nd ed., George Krauss, 2015