Quenched and Tempered (+QT700) 1.4313 Stainless Steel
EN 1.4313 +QT700 steel is EN 1.4313 stainless steel in the quenched and tempered condition. It has the second lowest strength compared to the other variants of EN 1.4313 stainless steel. The graph bars on the material properties cards below compare EN 1.4313 +QT700 steel to: wrought martensitic stainless steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Elastic (Young's, Tensile) Modulus
200 GPa 28 x 106 psi
Elongation at Break
15 %
Fatigue Strength
340 MPa 50 x 103 psi
Impact Strength: V-Notched Charpy
68 J 50 ft-lb
Poisson's Ratio
0.28
Shear Modulus
76 GPa 11 x 106 psi
Shear Strength
470 MPa 69 x 103 psi
Tensile Strength: Ultimate (UTS)
780 MPa 110 x 103 psi
Tensile Strength: Yield (Proof)
580 MPa 84 x 103 psi
Thermal Properties
Latent Heat of Fusion
280 J/g
Maximum Temperature: Corrosion
390 °C 740 °F
Maximum Temperature: Mechanical
780 °C 1430 °F
Melting Completion (Liquidus)
1450 °C 2630 °F
Melting Onset (Solidus)
1400 °C 2560 °F
Specific Heat Capacity
480 J/kg-K 0.11 BTU/lb-°F
Thermal Conductivity
25 W/m-K 14 BTU/h-ft-°F
Thermal Expansion
10 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
2.9 % IACS
Electrical Conductivity: Equal Weight (Specific)
3.3 % IACS
Otherwise Unclassified Properties
Base Metal Price
10 % relative
Density
7.8 g/cm3 490 lb/ft3
Embodied Carbon
2.4 kg CO2/kg material
Embodied Energy
34 MJ/kg 14 x 103 BTU/lb
Embodied Water
110 L/kg 13 gal/lb
Common Calculations
PREN (Pitting Resistance)
15
Resilience: Ultimate (Unit Rupture Work)
110 MJ/m3
Resilience: Unit (Modulus of Resilience)
870 kJ/m3
Stiffness to Weight: Axial
14 points
Stiffness to Weight: Bending
25 points
Strength to Weight: Axial
28 points
Strength to Weight: Bending
24 points
Thermal Diffusivity
6.7 mm2/s
Thermal Shock Resistance
28 points
Alloy Composition
| Fe | 78.5 to 84.2 | |
| Cr | 12 to 14 | |
| Ni | 3.5 to 4.5 | |
| Mn | 0 to 1.5 | |
| Mo | 0.3 to 0.7 | |
| Si | 0 to 0.7 | |
| C | 0 to 0.050 | |
| P | 0 to 0.040 | |
| N | 0 to 0.020 | |
| S | 0 to 0.015 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Further Reading
EN 10222-5: Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels
EN 10250-4: Open die steel forgings for general engineering purposes - Part 4: Stainless steels
Machining of Stainless Steels and Super Alloys: Traditional and Nontraditional Techniques, Helmi A. Youssef, 2016
EN 10088-3: Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 10088-1: Stainless steels - Part 1: List of stainless steels
Corrosion of Stainless Steels, A. John Sedriks, 1996
Advances in Stainless Steels, Baldev Raj et al. (editors), 2010