EN 1.4311 (X2CrNiN18-10) Stainless Steel
EN 1.4311 stainless steel is an austenitic stainless steel formulated for primary forming into wrought products. Cited properties are appropriate for the solution annealed (AT) condition. 1.4311 is the EN numeric designation for this material. X2CrNiN18-10 is the EN chemical designation.
This material is well established: the Further Reading section below cites a number of published standards, and that list is not necessarily exhaustive.
The graph bars on the material properties cards below compare EN 1.4311 stainless steel to: wrought austenitic stainless steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Mechanical Properties
Brinell Hardness
200
Elastic (Young's, Tensile) Modulus
200 GPa 29 x 106 psi
Elongation at Break
43 %
Fatigue Strength
270 MPa 40 x 103 psi
Impact Strength: V-Notched Charpy
93 J 68 ft-lb
Poisson's Ratio
0.28
Shear Modulus
77 GPa 11 x 106 psi
Shear Strength
450 MPa 65 x 103 psi
Tensile Strength: Ultimate (UTS)
650 MPa 94 x 103 psi
Tensile Strength: Yield (Proof)
310 MPa 45 x 103 psi
Thermal Properties
Latent Heat of Fusion
290 J/g
Maximum Temperature: Corrosion
420 °C 780 °F
Maximum Temperature: Mechanical
950 °C 1740 °F
Melting Completion (Liquidus)
1420 °C 2590 °F
Melting Onset (Solidus)
1380 °C 2510 °F
Specific Heat Capacity
480 J/kg-K 0.11 BTU/lb-°F
Thermal Conductivity
15 W/m-K 8.7 BTU/h-ft-°F
Thermal Expansion
16 µm/m-K
Electrical Properties
Electrical Conductivity: Equal Volume
2.4 % IACS
Electrical Conductivity: Equal Weight (Specific)
2.7 % IACS
Otherwise Unclassified Properties
Base Metal Price
16 % relative
Density
7.8 g/cm3 490 lb/ft3
Embodied Carbon
3.1 kg CO2/kg material
Embodied Energy
43 MJ/kg 19 x 103 BTU/lb
Embodied Water
140 L/kg 17 gal/lb
Common Calculations
PREN (Pitting Resistance)
21
Resilience: Ultimate (Unit Rupture Work)
230 MJ/m3
Resilience: Unit (Modulus of Resilience)
240 kJ/m3
Stiffness to Weight: Axial
14 points
Stiffness to Weight: Bending
25 points
Strength to Weight: Axial
23 points
Strength to Weight: Bending
21 points
Thermal Diffusivity
4.0 mm2/s
Thermal Shock Resistance
15 points
Alloy Composition
Among wrought stainless steels, the composition of EN 1.4311 stainless steel is notable for containing comparatively high amounts of chromium (Cr) and nickel (Ni). Chromium is the defining alloying element of stainless steel. Higher chromium content imparts additional corrosion resistance. Nickel is primarily used to achieve a specific microstructure. In addition, it has a beneficial effect on mechanical properties and certain types of corrosion.
| Fe | 65.7 to 73.9 | |
| Cr | 17.5 to 19.5 | |
| Ni | 8.5 to 11.5 | |
| Mn | 0 to 2.0 | |
| Si | 0 to 1.0 | |
| N | 0.12 to 0.22 | |
| P | 0 to 0.045 | |
| C | 0 to 0.030 | |
| S | 0 to 0.015 |
All values are % weight. Ranges represent what is permitted under applicable standards.
Followup Questions
Similar Alloys
Further Reading
EN 10222-5: Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels
EN 10272: Stainless steel bars for pressure purposes
EN 10250-4: Open die steel forgings for general engineering purposes - Part 4: Stainless steels
EN 10269: Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10088-3: Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 10088-1: Stainless steels - Part 1: List of stainless steels
Corrosion of Austenitic Stainless Steels: Mechanism, Mitigation and Monitoring, H. S. Khatak and B. Raj (editors), 2002
Austenitic Stainless Steels: Microstructure and Mechanical Properties, P. Marshall, 1984
Advances in Stainless Steels, Baldev Raj et al. (editors), 2010